PPR Plumbing Systems for Extreme Temperature
-
No Scaling, can withstand Higher'Ph' Values.
-
Good Chemical Resistance.
-
Leak Proof Joints.
-
Very Less Coefficient Of Friction.
-
Promotes hygiene by restricting bacterial growth.
Pipes
-
Monolayer Pipes (PN 20)
Size
(in mm)Std
Packaging20mm 110 25mm 60 32mm 45 40mm 30 50mm 18 63mm 8 75mm 8 90mm 5 110mm 4 160mm -
-
Triple Layer (PN 20)
Size
(in mm)Std
Packaging20mm 86 25mm 70 32mm 40 40mm 22 50mm 14 63mm 8 75mm 8 90mm 5 110mm 4 160mm -
-
Pipes (Black) (UV Resistance) (PN 20)
Size
(in mm)Std
Packaging20mm 86 25mm 60 32mm 36 40mm 30 50mm 18 63mm 8 75mm - 90mm - 110mm - 160mm -
-
Monolayer Pipes (PN 16)
Size
(in mm)Std
Packaging20mm 110 25mm 75 32mm 45 40mm 26 50mm 18 63mm 12 75mm 8 90mm 5 110mm 4 160mm 1
-
Triple Layer (PN 16)
Size
(in mm)Std
Packaging20mm 100 25mm 70 32mm 40 40mm 26 50mm 16 63mm 10 75mm 8 90mm - 110mm - 160mm 1
-
Pipes (Black) (UV Resistance) (PN 16)
Size
(in mm)Std
Packaging20mm 110 25mm 70 32mm 40 40mm 26 50mm 16 63mm 10 75mm 8 90mm 5 110mm 4 160mm -
-
Monolayer Pipes (PN 10)
Size
(in mm)Std
Packaging20mm 110 25mm 75 32mm 45 40mm 26 50mm 16 63mm 10 75mm 8 90mm 5 110mm 4 160mm 1
-
Triple Layer (PN 10)
Size
(in mm)Std
Packaging20mm - 25mm - 32mm 45 40mm 26 50mm 16 63mm 10 75mm 8 90mm 5 110mm 4 160mm -
-
Pipes (Black) (UV Resistance) (PN 10)
Size
(in mm)Std
Packaging40mm 26 50mm 16 63mm 10 - - - - - - - - - - - - - -
-
Pipes (Black) (3L-Thermex) (PN 20)
Size
(in mm)Std
Packaging20mm 86 25mm 60 32mm 36 40mm 22 50mm 14 63mm 8
-
Pipes (Black) (3L-Thermex) (PN 16)
Size
(in mm)Std
Packaging20mm 100 25mm 70 32mm 40 40mm 26 50mm 16 63mm 10
-
Pipes (3L-Thermex) (PN 10)
Size
(in mm)Std
Packaging40mm - 50mm - 63mm - - - - - - -
Fittings
Brass Insert
Fittings
Specifications
| Fittings | Pipes | |
|---|---|---|
| Material | Polypropylene - Random Copolymer (PP-R) | Polypropylene - Random Copolymer (PP-R) |
| Colour | Green | Single layer pipes Available in green & Triple layer pipes have outer layer in green colour |
| Reference Standards | DIN : 16962 | IS : 15801 - 2008 |
| Working Temperature | -20° C to 95° C | -20° C to 95° C |
| End Connections | Poly-fusion welding. fortranstion joints, fittings with threaded metal inserts are available. | Poly-fasion welding. |
Jointing Method
DO'S
-
CUTTING
Cut the pipe at a right angle to its axis using burr-free cutter.
Ensure that the pipe is free from burrs or cutting chips.
Clean the pipe & fitting perfectly before welding.
Mark welding depth at the end of pipe. -
HEATING
Mount the suitable dyes on the heating element of the welding machine according tothe diameter of pipe and fitting.
Connect the welding machine to 220 volts A.C. power supply.
Select 2600C temperature on the welding machine thermostat.
Wait until the required working temperature is reached.
Insert the pipe and the fitting in the dyes by exerting light pressure. -
WELDING
After heating, quickly insert the pipe into the fitting by exerting light pressure.
Any misalignment should be corrected immediately after insertion to avoid any stress in the weld.
Allow the joint to cool as per the cooling time given in table. -
STORAGE
Although Greenfit PP-R Pipe system material is stabilized for use at elevated temperatures do not expose the pipes & fittings to direct sunlight.
-
TRANSPORTATION
During transportation, Greenfit PP-R pipes should be loaded in a proper manner, otherwise pipes may get deformed.
-
PREPARATION FOR WELDING
Before welding/jointing, clean the surface of Greenfit PP-R Pipes & Fittings with a clean piece of cloth and then start welding.
-
WELDING
Avoid air droughts during welding to avoid stress in the welds.
-
SAFE WELDING
Do not cool welding machine in water.
-
BENDING
Do not apply direct flame to fabricate bends or crossover pipes, as the direct exposure to fire may cause damage to the Greenfit PP-R pipes. Use only hot air blowing equipment at 1400C. (Cross overs are readily available.)
-
INSTALLATION AT LOWER TEMPERATURE
At sub zero temperatures (00C & below) Greenfit PP-R Pipe system tends to break under impact. Therefore, installation at low temperatures should be done with care, and the pipe lines shall be insulated.
DONT'S
-
CUTTING
Do not cut slant/unevenly.
-
DEBURRING AND RIDGE REMOVAL
Do not proceed with installation of pipe without deburring as the burr when heated will create an extra blockage inside the pipe.
-
CLEANING & MARKING
Do not proceed without cleaning as it will create problems during welding due to the presence of dirt or mud.
-
WELDING JOINT
1) Do not set the temperature of the heater higher or lower than 260°C.
2) Do not initiate the jointing process without gloves.
3) Misalignment of jointing to be corrected immediately before cooling, so as to avoid stress in the weld. -
STORAGE
Greenfit PP-R Pipe storage height should not be more than 1.5 meter.
-
HANDLING
The Greenfit PP-R Pipe system should be protected from impact of hard and sharp objects.
-
HEATING
While welding of Greenfit PP-R Pipes and fittings check that the thermostat of welding machine and dyes have reached correct temperature (2600C). While welding, the pipe must not be twisted.
-
SAFE WELDING
Welding machines shall be earthed properly during use.
-
THREAD JOINT
Do not over tighten threaded fittings & valves.
-
BENDING
While bending the pipe, the bending radius shall be more than 8 times the diameter of the pipe.
-
OUTDOOR INSTALLATION
Use 3 layered pipes for outdoor application.